Digi-tv.ee

kas oskab keegi kommenteerida miks menüül(OSD) või kanali vahetamisel "infobar'il" jäävad vahest osad tükid puudu ja paistab läbi? vahest isegi volüümi riba poolik. viimasel 4.31 geminil eriti ei pand enam tähele seda jama, aga krt seda ei julge kasutada.

tundub, et ma pole ainuke kellel see jama. enne sellest vist arutatud ei ole, vähemalt dreamboxi teemast ei leidnud.

Seda teeb tõenäoliselt gSUB. Kahjuks tekib selline kõrvalnähtus. Vanemad versioonid nii ei jama, see on v2.06 ja 2.07 probleem.

rimas kirjutas:Seda teeb tõenäoliselt gSUB. Kahjuks tekib selline kõrvalnähtus. Vanemad versioonid nii ei jama, see on v2.06 ja 2.07 probleem.

need viimased, enne neid oli ka nagu probleeme. ma kahtlustan mingit gemini seade viga, sest 4.31 töötas ilusti. peaks ainult puhta geminiga proovima, ma alati kohe ccCam ja gsub peale lasknud. hetkel kui OK nuppu vajutan, siis üle ühe korra on kanalilist poolik või ei näe midagi, ainult üksikud kuubikud ees.

Kui gSUB 'i viga, lase maha ja proovi bullztext'i.

Ei kasuta Geminit, minul on see probleem iga imagega, kuhu gSUB installitud. Kui gSUB killida on kõik normis. Eelistan siiski gSUB'i bullztext'ile. Saab valida fonti, rea kõrgust, audio keelt. Ja kirjeldatud probleem ei esine pidevalt. Kui asi hakkab juba väga häirivaks muutuma killin gSUB'i ja enigma restart. Siis jälle tükiks ajaks kõik korras.

tundub, et asi ongi gSubis. lasin eila maha ja siiani toimind 5+. huvitav kas vanemad versioonid ka nii teevad? proovisin seda bullstexti ka, sellega korras, aga proge natuke liiga primitiivne. nagu juba mainiti, kasutan ise ka neid võimalusi mida pakub gSub.

rimas kirjutas:Eelistan siiski gSUB'i bullztext'ile. Saab valida fonti, rea kõrgust, audio keelt.

Täpselt samu asju saab ka valida bullztext'iga. Samuti subtiitrite värvi ja subtiitrite põhja värvi.

tigekala kirjutas:

rimas kirjutas:Eelistan siiski gSUB'i bullztext'ile. Saab valida fonti, rea kõrgust, audio keelt.

Täpselt samu asju saab ka valida bullztext'iga. Samuti subtiitrite värvi ja subtiitrite põhja värvi.

just, tuleb lihtsalt fail käsitsi üle näppida.

Kuidas bullztext' i fonti valida. See teleteksti oma näeb jube välja, minu telekal puudub ka õ täht

# Config file for bullz_text (Version 0.41)
# This file should be copied to /var/etc in the dreambox
#
#
# Tells the level of output. Higher value means more output and 0
# means only serious level. Valid values are 0,1,2 and 3 (default is 1)
# The label time_stamp tells that you want the output timestamped
#
verbose: 1
time_stamp: 0
#
# The kernel DVB API exist in several versions. Normally will the old-fashioned
# work, which I call 2 (This is default). Bullz_text will also support version 3
# Version 4 is so new so we will se .......
#
dvb_api: 2
#
# Normally all trace and error will print to the serial
# which are the serial port. You can change this to some
# other destination. Default is Serial port
# If you use the serial port for other tasks you
# must change this to another thing
#
# 1: Output to the serial port (115200 bps)
# 2: Output to the 'stderr' in your window. This can only be used
# as forground execution. (If background fallback to mode1)
# 3: Output to Unix socket (File name: /tmp/.bullz_console)
# 4: Output to TCP socket (Port Number: 4252 [ BT as hex ]);
#
console: 1
#
# Fatal errors are normally written on the TV-screen. If you don't want
# this feature set the parameter show_fatal to off.
#
show_fatal: on
#
# Choose languages: Possible values are 'nor' 'swe' 'dan' 'deu' 'dut' 'fin' 'fra' 'ita' 'por'
# 'spa' and 'eng'
# Default for the primary language is swe (Swedish). The secondary language is set to 1st
# The secondary language can also be set to first available with '1st'
# The secondary language will only appear if the primary language is missing in the stream
#
language: fin
language2: 1st
#
# Some channels have different Audio Language. If you want to Bullz_text to make
# audio changes in the same manner as subtitle just set the flag audio_change to 'on'
# The default value is 'off'. It will also change from Stereo to mono in the case
# the channel have different language
# The language is taken from 'audio_language','language' and 'language2' in that order
# Some Spanish channel use 'dos' as the second language which (I think) the original
# language. The parameter audio_dos tells to use 'dos' language
#
audio_change: off
audio_language: eng
audio_dos: off
#
# It is possible to use an external file which can handle the font generation.
# default will the builtin font be used so this can be left out
#
# fontfile: /var/etc/bullz_text.fnt
#
#
# If you are using http authentification and also change password
# you must tell the new password in this config file
# The default value is user: root and password :dreambox
# Notice the syntax 'username:password'.
#
auth: root:dreambox
#
# The ISP for the Nordic channel Kiosk are sending wrong character for some
# nordic characters. To use the build in font-patch just uncomment
# the desired patch below.
#
#
# nor_patch: 1
# dan_patch: 1
#
# Some French channel do some wrong understanding of the specification
# The parameter fra_error is an or-ed parameter with bits 1,2,4 .....
#
# Bit 1: (0x01) means that that it should make a decimal uncoding of the pagenumber
# instead of hexadecimal(Like canal +)
# Bit 2: (0x02) means that it also should show pages without the subtitle flag. (Like multivision)
#
# fra_error: 3
#
# Some channels send subtitle in teletext but make no annocement in the PMT packet.
# This can be solved by helping bullz_text by this. Use the keyword PMT2page followed
# the PMT-id and pagenumber. The easiest way to get the PMT-id is to double press
# the INFO key. Not that you need the decimal value written in parentes.
# This method is bad as it can be more Channels with the same PMT-id
#
# Example From German Premiere 1-5 on Astra
#
# PMT2page: 101 151
# PMT2page: 103 152
# PMT2page: 109 153
# PMT2page: 102 154
# PMT2page: 106 155
#
#
# The forground and background color is customable. This can be done in two
# ways. Either raw or preconfigured way. If both ways is used will the latest
# in this file be valid.
#
# The preconfigured values are: (New values from version 0.30)
# 0: As teletext behavior (white on black with color option)
# 1: white on black
# 2: white on halftransparent
# 3: black on halftransparent
# 4: black on white
# 5: white on transparent
# 6: yellow on transparent
# 7: white on transparent and outline
# 8: white on halftransparent and outline
# 9: yellow on transparent and outline
#
# Thew default value is colorindex equal to 0
#
colorindex: 7
#
# When looking at 16:9 movie in 4:3 format (letterbox) will the subtitle come too low for the movie.
# With the parameter delta_y you can move the lines up/down.
# The following values are valid. (default is 5). Note that the text will be moved in all screen formats
#
# 0: Lines moved 2.5 character size up
# 1: Lines moved 2 character size up
# 2: Lines moved 1.5 character size up
# 3: Lines moved one character size up
# 4: Lines moved half character size up
# 5: The correct position as original teletext
# 6: Lines moved half character size down
#
delta_y: 5
#
# The space between characters can be change with the parameter x_space. This parameter
# can vary between 0 to 5. (5 is the most narrowed and 0 is the widest). The default
# value is 3. (Bullz_text version 0.40 and earlier used staticly 2)
#
#
x_space: 3
#
# It is also possible to suspend the output just during the user interaction
# with the menues of the enigma window manager. Just choose this to 'on'
# or 'off'
avoid_frames: on
#
# The subtitle can have a timestamp for every text. With this flag can the program
# look at time and make a delay. The flag has the value on/off (on is default)
# Note that some channel (like kiosk) dont have any timestamp and in that
# case will this flag be ignored
#
#
synctext: on
#
# If the subtitle come to early when you execute from the harddisc you can use
# the feature delay subtitle. It will only work in the case that the subtitle
# have no timestamp. If the subtitle have timestamp (pts) this feature is always off
# The time to delay is measured in milliseconds
#
delay_sub: off
delay_time: 2000
#
# Normally you want to have bullz_text to start at boot. This is done if the flag
# at_boot is set to on. If you always want to start manually set the flag to off.
# The default value is on
at_boot: on

ja kui driimi password on vahetatud siis see kah ära muuta.

Kui poleks gSUB' i, kasutaks bullzztext' i rõõmuga. Praegu tundub see siiski suure tagasiminekuna. Exploreril ja Historyl tuleb eesti teksti asemel soome oma (vähemalt minul) ja fonti ma ka muuta ei oska.

Mul küll gSubiga senini probleeme pole olnud. Kuigi jah, Gemini on 2.7 , üks lollikindlamaid versioone, mis teeb kõik vajaliku ära ja boxi kinnijooksmine, omast peast restartimine jm kuuldud hädad on võõrad mured.

panin prooviks gsub 1.08 ja paar päeva ilusti jooksnud.