16 sisendiga diseq.. kuidas töötab?

[tigekala]

16/1 töötab mul paremini DM 800-ga see oleneb ju tüünerist ka, üldiselt dream ei jonni, mingid no name tüünerid ei taha vist nii hästi tunnistada...

Jonnib ikka. Üldiselt Dream mingeid mustlaste ( haltuura) noname DISEqC-id ei taha tunnistada.

[tramm]

Loen Centauri spetsi. Insertion Loss 5 dB 950-2150 MHz satellite band, 2dB 5-862 MHz terrestial band.Isolation between inputs: 25dB min. Centaur toodetud firmas EMP-Centauri Czech Republic.

[kitt]

Kas see isend EM P-CENTAURI 16/1 dreambox 7020 ka tööle hakkab jamasin terve mitu head tundi. Kui ma oma 12 lnb sisse lükkan ei tule läbi peale siiruse mis on kolmas sisend ja kui jätta ainult 3 lnb järgi probleemi pole nii kui lisad 4 või 5 teised läinud aga siirus on. Ja see lüliti mis seal küljes on ei muuda küll midagi. Sai ju see veel osta siit http://www.lobster.ee/sat/index.php?bm= ... nodeID=443 või on mingi praak toode.

[mustkass]

Lüliti peab olema asendis 1.1,töötab kenasti mul juba mitu head aastat,siis on sul seal settingud valed pane skriin mis settingud on näiteks ühel peal,kõik peavad olema ühtemoodi(v.a. peade järjekorra numbrid) v.a. venelaste 36e ei teeks ka paha kirja panna mis imaget kasutad.

[andres66]

Kas see isend EM P-CENTAURI 16/1 dreambox 7020 ka tööle hakkab jamasin terve mitu head tundi. Kui ma oma 12 lnb sisse lükkan ei tule läbi peale siiruse mis on kolmas sisend ja kui jätta ainult 3 lnb järgi probleemi pole nii kui lisad 4 või 5 teised läinud aga siirus on. Ja see lüliti mis seal küljes on ei muuda küll midagi. Sai ju see veel osta siit http://www.lobster.ee/sat/index.php?bm= ... nodeID=443 või on mingi praak toode.

Lüliti asend loeb.
DIP lüliti tuleb ''ainult 1.1'' seadesse panna ja nn. reset teha 16x1 lülitile.

Kunagi päris alguses ma ka korra jamasin seepärast, et tuuner oli toas taga juba ( eelmisest 8x1 lülitist ja diseqc 1.1 seadetega),
DIP algselt ei olnud uuel lülitil ''ainult 1.1'' asendis ja
siis niisama muutes DIP asendit, hakkas poolvigaselt toimetama.

Instruction manual
Connection
Product S
16/1
PCP-W3 is a multi-mode satellite DiSEqC switch, designed for connecting of up to 16 satellite converters
(LNBs) and terrestrial antenna to 1 user. Before installation, remove the product from plastic shield and connect coaxial
cables from each LNB into satellite input ports (“SAT1 IN” to “SAT16 IN”). It is recommended to write down assignment of
inputs for receiver's setup and future reference. If required, connect cable from terrestrial antenna into port “TERR IN” and use
appropriate wall socket or frequency splitter to separate satellite and terrestrial bands on user end of coaxial cable. Note: there
is no DC feed provided on terrestrial input.
Modes of operation
Set desired operation mode by means of DIP switch located on rear side of metal housing. There are four modes of operation
available:
1) DiSEqC 1.0 (committed switch - position/option A to D, available inputs 1 to 4)
2) DiSEqC 1.1 (uncommitted switch 1 to 16)
3) combined DiSEqC 1.0 & 1.1 (committed switch - position/option
A to D, uncommitted switch 1 to 4)
4) DiSEqC 1.2 (16 motor positions)
Mode selection guide
Use DiSEqC 1.1 mode, if your receiver supports uncommitted switch parameter 1 to 16. Use DiSEqC 1.0 & 1.1 mode, if your
receiver supports uncommitted switch parameter 1 to 4 only. In this case set committed switch as well. If the receiver doesn't
support DiSEqC 1.1 mode at all, use DiSEqC 1.2 mode and carry out configuration procedure for motorized antenna.
See product sticker located on plastic shield for detailed information on DIP switch levers positions (ON position is set when
the lever is pressed down) and required DiSEqC parameters.
Note: mode setting change (DIP switch levers positions) will take
affect only after reset is performed: Disconnect the product from the receiver and reconnect it again after several seconds.
Receiver's configuration procedures may. Please follow instruction manual of Your receiver.
After successful setup, reinsert metal box back into plastic cover and fix on the final position.
Extension options
In basic configuration, single universal LNBs are expected to be used with the product. For dual tuner receiver, twin LNBs
should be used along with 2 pcs of S
16/1
PCP-W3 switch. For reception on several set-top-boxes, the corresponding number
of the switches must be used and appropriate LNBs installed (twin, quad, octo).
In case of more than 16 LNB are to be switched, install 2 pcs of S
16/1
PCP-W3, configure them in DiSEqC 1.1 mode and use
suitable DiSEqC 1.0 / DiSEqC 2.0 switch for switching between S
16/1. Consult your dealer or check manufacturer's website
http://www.emp-centauri.cz for possible solutions.
Troubleshooting
If there is no signal from single LNB, while others are running, check possibility of short circuit or bad connection on affected
input. (Product itself is protected against short circuit condition on all satellite inputs.)
----------------------------

16x1_diseqc-1.1_seaded.jpg

[kitt]

Enne oli 1o diseq vahel siis panin 16 külge ja sealt see kõik alguse sai. See lüliti peab olema et 1 1 siis esimene alla ja teised 3 üleval. Aga kui kõik üleval 1.0 tulevad ka kõik kolm säti ka läbi või peabki nii. DB tarkvara Open pli 4 ja ma ei muutnud tuuneri seaded on kõik samad mis 10 diseq puhul

[kitt]

Andres66 need seaded on kõik nii nagu sinul see on ok kuid kuidas 16 reset teha

[tigekala]

Välja arvatud, et sul on siiamaani DiseqC protokoll - 1.0

Aga kui kõik üleval 1.0 tulevad ka kõik kolm säti ka läbi või peabki nii.

[mustkass]

Andres66 need seaded on kõik nii nagu sinul see on ok kuid kuidas 16 reset teha

Note: mode setting change (DIP switch levers positions) will take
affect only after reset is performed: Disconnect the product from the receiver and reconnect it again after several seconds.

Enne ikka diseq tagapaneelil pane see liugur 1.1 peale ja seejärel restart nagu eelpool kirjas.

[kitt]

Teen selle reseti homme ära praegu 1/10 taga ja pole probleemi eks näis mis saab